Black Spirals On A White Stripe On Black Pants

I made another pair of pants.

The pattern is almost the same as the one I used for the previous pair, but with the addition of a stripe down the side.

I trimmed a total of 5-cm off the side seam edges and made a 5-cm wide stripe.

The pants are made entirely out of denim and sewn with heavy duty thread.

I still don't think I have the fall front construction completely figured out. It might be a bit easier to sew by hand than machine. At least I remembered to put the flaps in this time instead of just binding the under side of the placket.

I used a flat felled seam to sew the side piece in.

The seam allowance is stitched down with regular thread.
You can see where the heavy duty thread causes trouble with the tension.

I painted spirals on the stripe before sewing up the inseam, except for a little bit at the bottom and top, which I left until last. The spirals are traced in pencil first and then painted on with Speedball fabric printing ink. It's meant for screen printing, but painting it on works just fine.
The painting is a little sloppy up close because I foolishly put the right side out, when the wrong side is actually a much better painting surface.

The inseam and crotch seam are just serged.

The waistband is machine sewn, except for the inside edge.

The pants are hemmed by hand. I forgot to take a picture of the completed front, but it's almost the same as the previous one.

The pants are a little tighter than I wanted them to be, partly because the denim doesn't have any stretch, but also because a bit of the width mysteriously disappeared during the pattern alteration. I'll have to re-measure the pieces and correct it.
Luckily they still fit comfortably.

I'm not used to working with such heavy fabric, so the construction isn't quite as neat as I'd like it to be.

I really, really like this pattern and will be making it up many more times. Think of all the decorative things you can do with a 5-cm stripe!

White Linen Shirt With Pleated Ruffles

I finished my shirt!
I am so very happy with how it turned out.

The fabric is 100% linen. I used the measurements given in the Early American Life article, with a few changes based on the cotton shirt I tested the pattern with.

Measurements for the pieces are as follows:

Main Body: 25" x 30"- cut 2

Sleeves: 25" x 25"- cut 2

Collar: 8" x 16.5"- cut 1

Cuffs: 9" x 3"- cut 4

Shoulder Reinforcements: 20" x 6.5"- Cut 2

Shoulder Strips: 3" x 9.5"- cut 2

Underarm Gussets: 5" x 5"- cut 2

Hem Gussets: 2" x 2"(triangular)- cut 4

Neck Gussets: 4" x 4"(triangular)- cut 4

Ruffles: 2.5" wide by 2-3 times the length of the edge that they will be attached to.

All of the cut out pieces.

The only fine linen thread I had was brown, so I just used it for the structural bits. I used white silk thread for all of the finishing. I pre- waxed my threads and ironed them in a folded sheet of paper, a trick I read about on Victorian Tailoring. They worked so much better this way! The fabric didn't strip any of the wax off like it usually does and there was barely any knotting.

I sewed the shoulder seam, wrong sides together, with a backstitch. The seam was pressed open and the triangular neck gussets sewn on either end of the neck opening, on both the top and the bottom.

The shoulder strips went over top of them. They were attached with a backstitch, as were the gussets.

The finished shoulder seam.

For the ruffles I used a fabric from my grandmother's stash. I can't be certain, but I think it's linen. It's quite fine and crisp. It's only 18.5 inches wide, so I cut all the ruffles that length and left the selvedges on the ends.

The neck ruffle was cut 5" wide and hemmed on both edges with a running stitch.
I marked a line down the CF of the shirt body and down the middle of the ruffle. I box pleated it to the CF line, and it ended up going about 7" down the front of the shirt.

I basted the pleats down, and then basted a thin rectangle of the ruffle material over top of them.

Backstitching the pleats on.

I then sewed around the CF line, through all the layers, from the wrong side.

From the right side.

I cut down the line, turned the facing rectangle to the inside, turned the edges in and stitched them down using a running stitch.

I backstitched the collar edge to the neck hole, gathering all the single-layer parts of the neck opening.

I back stitched the other edge of the collar to the inside edge of the opening, tucked in the allowances of the collar ends and backstitched them closed too.

Finished collar.

The sleeves were gathered to 19" and backstitched to the shoulders,  leaving 9.5" of sleeve on either side of the shoulder seam. The shoulder reinforcements were stitched onto the same seam, and sewn down with a  running stitch.

The shoulder reinforcement on the inside of the shirt.

I sewed the square gusset in underneath the sleeve, and then sewed up the side seam and the sleeve seam, leaving a 4" vent at the end of each. These seams are flat felled, and all done with a running stitch.

The edges of the vents were hemmed, as was the bottom of the shirt, with a running stitch.
The hem gussets were sewn to the split in the side seam in the same manner as the neck gussets.

Thanks to post- tropical storm Arthur, our power was out for a week, so some of this part was sewn by candle light.

I was careful not to get wax on anything.

Flat felling the seams left little raw edges at the corners of the gusset and the place where the sleeve vent starts. I sewed buttonhole stitches over them so they wouldn't fray.

The sleeve vent.

The cuff ruffles were just like the neck ruffles, only cut half as wide and only hemmed on one edge.

I box pleated them to the cuff pieces.

And basted them on.

Then I basted the other halves of the cuffs on, so that the pleats were nicely sandwiched.

And sewed through all the layers with a backstitch.

I graded the seam allowances.

A cuff about to be attached.

The cuffs were attached in pretty much the same way as the collar.

Sewing on the cuff.

And the other side of the cuff.

I had to stab stitch the ends of the cuffs closed because backstitching made them look really wonky.

The buttons are thread buttons!
I made them using very thick linen thread. I followed the method shown on this Victorian Tailoring post.

Making buttonhole stitches.

I found a little bone awl in my grandmother's sewing box that was just the right size.

I'm not sure if you're supposed to wax the thread you use for thread buttons, but I did, and it made them very firm. When I stitched the little x on the back I had to pull the needle through with pliers.

The underside of a finished button.

There are two on the collar and two on each cuff.

Aren't they cute? I think they could be used for the little
white sprigs in a flower bouquet.

The wax makes them look brown against the white linen, but that's okay since they aren't meant to show when one is fully dressed.

The collar.

And that's it!
I considered adding a laundry mark(my initials in red cross- stitch) but decided there was no point. Nobody is going to be confused about whose shirt this is, and I can always add one later if I want to.

I love this shirt! It's very comfortable, the collar is the right height, and the ruffles look perfect. The ruffles on the previous shirt were far too long. I think these ones could stand to be 1cm longer, but no more.

Wrist ruffles and claws go so nicely together.

The Challenge: # 13- Under $10

Fabric: Soft linen, crisp probably- linen.

Pattern: From a magazine article, with a few alterations by me. All the measurements are given in the post above.

Year: Second half of the 18th century.

Notions: Thin linen thread, silk thread, thick linen thread.

How historically accurate is it? Very. I can safely say that this is the most accurate thing I have ever made. Edit(Feb. 2020) HAHAHAHAHA, nope! Not accurate for a multitude of reasons!

Hours to complete: Unknown

First worn: July 14th, 2014

Total cost: Less than a dollar. The only thing I bought was the silk thread.

I tried it on with my unfinished coat to see if the ruffles would stick out the right amount, and they did!

I should look into ordering linen online, because I want to make a lot more of these, and I'm not going to find the appropriate fabric in this city.